| 1. |
- Ail, Ujwala, et al.
(författare)
-
Effect of Sulfonation Level on Lignin/Carbon Composite Electrodes for Large-Scale Organic Batteries
- 2020
-
Ingår i: ACS Sustainable Chemistry and Engineering. - : AMER CHEMICAL SOC. - 2168-0485. ; 8:49, s. 17933-17944
-
Tidskriftsartikel (refereegranskat)abstract
- The key figure-of-merit for materials in stationary energy storage applications, such as large-scale energy storage for buildings and grids, is the cost per kilo per electrochemical cycle, rather than the energy density. In this regard, forest-based biopolymers such as lignin, are attractive, as they are abundant on Earth. Here, we explored lignin as an electroactive battery material, able to store two electrons per hydroquinone aromatic ring, with the targeted operation in aqueous electrolytes. The impact of the sulfonation level of lignin on the performance of its composite electrode with carbon was investigated by considering three lignin derivatives: lignosulfonate (LS), partially desulfonated lignosulfonate (DSLS), and fully desulfonated lignin (KL, lignin produced by the kraft process). Partial desulfonation helped in better stability of the composite in aqueous media, simultaneously favoring its water processability. In this way, a route to promote ionic conductivity within the lignin/carbon composite electrodes was developed, facilitating the access to the entire bulk of the volumetric electrodes. Electrochemical performance of DSLS/C showed highly dominant Faradaic contribution (66%) towards the total capacity, indicating an efficient mixed ionic-electronic transport within the lignin-carbon phase, displaying a capacity of 38 mAh/g at 0.25 A/g and 69% of capacity retention after 2200 cycles at a rate of 1 A/g.
|
|
| 2. |
- Ajjan, Fátima, 1986-, et al.
(författare)
-
Doped Conjugated Polymer Enclosing a Redox Polymer : Wiring Polyquinones with Poly(3,4‐Ethylenedioxythiophene)
- 2020
-
Ingår i: Advanced Energy and Sustainability Research. - : John Wiley & Sons. - 2699-9412. ; 1:2
-
Tidskriftsartikel (refereegranskat)abstract
- The mass implementation of renewable energies is limited by the absence of efficient and affordable technology to store electrical energy. Thus, the development of new materials is needed to improve the performance of actual devices such as batteries or supercapacitors. Herein, the facile consecutive chemically oxidative polymerization of poly(1-amino-5-chloroanthraquinone) (PACA) and poly(3,4-ethylenedioxythiophene (PEDOT) resulting in a water dispersible material PACA-PEDOT is shown. The water-based slurry made of PACA-PEDOT nanoparticles can be processed as film coated in ambient atmosphere, a critical feature for scaling up the electrode manufacturing. The novel redox polymer electrode is a nanocomposite that withstands rapid charging (16 A g−1) and delivers high power (5000 W kg−1). At lower current density its storage capacity is high (198 mAh g−1) and displays improved cycling stability (60% after 5000 cycles). Its great electrochemical performance results from the combination of the redox reversibility of the quinone groups in PACA that allows a high amount of charge storage via Faradaic reactions and the high electronic conductivity of PEDOT to access to the redox-active sites. These promising results demonstrate the potential of PACA-PEDOT to make easily organic electrodes from a water-coating process, without toxic metals, and operating in non-flammable aqueous electrolyte for large scale pseudocapacitors.
|
|
| 3. |
- Anctil, Annick, et al.
(författare)
-
Status report on emerging photovoltaics
- 2023
-
Ingår i: JOURNAL OF PHOTONICS FOR ENERGY. - : SPIE-SOC PHOTO-OPTICAL INSTRUMENTATION ENGINEERS. - 1947-7988. ; 13:4
-
Tidskriftsartikel (refereegranskat)abstract
- This report provides a snapshot of emerging photovoltaic (PV) technologies. It consists of concise contributions from experts in a wide range of fields including silicon, thin film, III-V, perovskite, organic, and dye-sensitized PVs. Strategies for exceeding the detailed balance limit and for light managing are presented, followed by a section detailing key applications and commercialization pathways. A section on sustainability then discusses the need for minimization of the environmental footprint in PV manufacturing and recycling. The report concludes with a perspective based on broad survey questions presented to the contributing authors regarding the needs and future evolution of PV.(c) 2023 Society of Photo-Optical Instrumentation Engineers (SPIE)
|
|
| 4. |
- Bian, Qingzhen, et al.
(författare)
-
Reduced Nonradiative Voltage Loss in Terpolymer Solar Cells
- 2020
-
Ingår i: Journal of Physical Chemistry Letters. - : American Chemical Society (ACS). - 1948-7185. ; 11:10, s. 3796-3802
-
Tidskriftsartikel (refereegranskat)abstract
- The dissociation of hybrid local exciton and charge transfer excitons (LE-CT) in efficient bulk-heterojunction nonfullerene solar cells contributes to reduced nonradiative photovoltage loss, a mechanism that still remains unclear. Herein we studied the energetic and entropic contribution in the hybrid LE-CT exciton dissociation in devices based on a conjugated terpolymer. Compared with reference devices based on ternary blends, the terpolymer devices demonstrated a significant reduction in the nonradiative photovoltage loss, regardless of the acceptor molecule, be it fullerene or nonfullerene. Fourier transform photocurrent spectroscopy revealed a significant LE-CT character in the terpolymer-based solar cells. Temperature-dependent hole mobility and photovoltage confirm that entropic and energetic effects contribute to the efficient LE-CT dissociation. The energetic disorder value measured in the fullerene- or nonfullerene-based terpolymer devices suggested that this entropic contribution came from the terpolymer, a signature of higher disorder in copolymers with multiple aromatic groups. This gives new insight into the fundamental physics of efficient LE-CT exciton dissociation with smaller nonradiative recombination loss.
|
|
| 5. |
- Bian, Qingzhen, 1988-, et al.
(författare)
-
Vibronic coherence contributes to photocurrent generation in organic semiconductor heterojunction diodes
- 2020
-
Ingår i: Nature Communications. - : NATURE PUBLISHING GROUP. - 2041-1723. ; 11:1
-
Tidskriftsartikel (refereegranskat)abstract
- Charge separation dynamics after the absorption of a photon is a fundamental process relevant both for photosynthetic reaction centers and artificial solar conversion devices. It has been proposed that quantum coherence plays a role in the formation of charge carriers in organic photovoltaics, but experimental proofs have been lacking. Here we report experimental evidence of coherence in the charge separation process in organic donor/acceptor heterojunctions, in the form of low frequency oscillatory signature in the kinetics of the transient absorption and nonlinear two-dimensional photocurrent spectroscopy. The coherence plays a decisive role in the initial 200 femtoseconds as we observe distinct experimental signatures of coherent photocurrent generation. This coherent process breaks the energy barrier limitation for charge formation, thus competing with excitation energy transfer. The physics may inspire the design of new photovoltaic materials with high device performance, which explore the quantum effects in the next-generation optoelectronic applications.
|
|
| 6. |
- Chen, Xian-Kai, et al.
(författare)
-
A unified description of non-radiative voltage losses in organic solar cells
- 2021
-
Ingår i: Nature Energy. - : Springer Nature. - 2058-7546. ; 6:8, s. 799-806
-
Tidskriftsartikel (refereegranskat)abstract
- Organic solar cells based on non-fullerene acceptors have enabled high efficiencies yet their charge dynamics and its impact on the photovoltaic parameters are not fully understood. Now, Chen et al. provide a general description of non-radiative voltage losses in both fullerene and non-fullerene solar cells. Recent advances in organic solar cells based on non-fullerene acceptors (NFAs) come with reduced non-radiative voltage losses (Delta V-nr). Here we show that, in contrast to the energy-gap-law dependence observed in conventional donor:fullerene blends, the Delta V-nr values in state-of-the-art donor:NFA organic solar cells show no correlation with the energies of charge-transfer electronic states at donor:acceptor interfaces. By combining temperature-dependent electroluminescence experiments and dynamic vibronic simulations, we provide a unified description of Delta V-nr for both fullerene- and NFA-based devices. We highlight the critical role that the thermal population of local exciton states plays in low-Delta V-nr systems. An important finding is that the photoluminescence yield of the pristine materials defines the lower limit of Delta V-nr. We also demonstrate that the reduction in Delta V-nr (for example, <0.2 V) can be obtained without sacrificing charge generation efficiency. Our work suggests designing donor and acceptor materials with high luminescence efficiency and complementary optical absorption bands extending into the near-infrared region.
|
|
| 7. |
- Fan, Qunping, 1989, et al.
(författare)
-
Over 14% efficiency all-polymer solar cells enabled by a low bandgap polymer acceptor with low energy loss and efficient charge separation
- 2020
-
Ingår i: Energy & Environmental Science. - : Royal Society of Chemistry. - 1754-5692 .- 1754-5706. ; 13:12, s. 5017-5027
-
Tidskriftsartikel (refereegranskat)abstract
- Obtaining both high open-circuit voltage (V-oc) and short-circuit current density (J(sc)) has been a major challenge for efficient all-polymer solar cells (all-PSCs). Herein, we developed a polymer acceptor PF5-Y5 with excellent optical absorption capability (onset extending to similar to 880 nm and maximum absorption coefficient exceeding 105 cm(-1) in a film), high electron mobility (3.18 x 10(3) cm(2) V-1 s(-1)) and high LUMO level (-3.84 eV) to address such a challenge. As a result, the PBDB-T:PF5-Y5-based all-PSCs achieved a high power conversion efficiency of up to 14.45% with both a high Voc (0.946 V) and a high Jsc (20.65 mA cm(-2)), due to the high and broad absorption coverage, small energy loss (0.57 eV) and efficient charge separation and transport in the device, which are among the best values in the all-PSC field. In addition, the all-PSC shows a similar to 15% improvement in PCE compared to its counterpart small molecule acceptor (Y5)-based device. Our results suggest that PF5-Y5 is a very promising polymer acceptor candidate for applications in efficient all-PSCs.
|
|
| 8. |
- Fernandez-Benito, Amparo, et al.
(författare)
-
Green and Scalable Biopolymer-Based Aqueous Polyelectrolyte Complexes for Zinc-Ion Charge Storage Devices
- 2023
-
Ingår i: ChemElectroChem. - : WILEY-V C H VERLAG GMBH. - 2196-0216. ; 10:2
-
Tidskriftsartikel (refereegranskat)abstract
- Green and scalable materials are essential to fulfill the need of electrification for transitioning into a fossil-fuels free society, and sustainability is a requirement for all new technologies. Rechargeable batteries are one of the most important elements for electrification, enabling the transition to mobile electronics, electrical vehicles and grid storage. We here report synthesis and characterization of polyelectrolyte complexes of alginate and chitosan, both biopolymers deriving from the sea, for transport of zinc ions in hydrogel electrolytes. We have used vibrational spectroscopy, thermal measurements and microscopy, as well as transport measurements with ohmic or blocking contacts. The transference number for zinc ions is close to 1, the conductivity is approximate to 10 mS/cm, with stability at Zn interfaces seen through 7000 cycles in symmetric zinc//zinc cell. A zinc ion aqueous electrolyte was prepared from blends of chitosan and alginate, by using a simple and scalable route. These green zinc ion electrolytes exhibit a stability window up to 2 V, a zinc ion transference number close to 1, and electrochemical cyclability over 7000 cycles at interfaces to zinc. This biologically derived polyelectrolyte complex offers many possibilities for optimizing transport and stability at electrode interfaces.image
|
|
| 9. |
- Harillo-Baños, Albert, et al.
(författare)
-
High-Throughput Screening of Blade-Coated Polymer:Polymer Solar Cells: Solvent Determines Achievable Performance
- 2022
-
Ingår i: ChemSusChem. - : Wiley. - 1864-5631 .- 1864-564X. ; 15:4
-
Tidskriftsartikel (refereegranskat)abstract
- Optimization of a new system for organic solar cells is a multiparametric analysis problem that requires substantial efforts in terms of time and resources. The strong microstructure-dependent performance of polymer:polymer cells makes them particularly difficult to optimize, or to translate previous knowledge from spin coating into more scalable techniques. In this work, the photovoltaic performance of blade-coated devices was studied based on the promising polymer:polymer system PBDB-T and PF5-Y5 as donor and acceptor, respectively. Using the recently developed high-throughput methodology, the system was optimized for multiple variables, including solvent system, active layer composition, ratio, and thickness, among others, by fabricating more than 500 devices with less than 24 mg of each component. As a result, the power conversion efficiency of the blade-coated devices varied from 0.08 to 6.43 % in the best device. The performed statistical analysis of the large experimental data obtained showed that solvent selection had the major impact on the final device performance due to its influence on the active layer microstructure. As a conclusion, the use of the plot of the device efficiency in the Hansen space was proposed as a powerful tool to guide solvent selection in organic photovoltaics.
|
|
| 10. |
- Khan, Ziyauddin, et al.
(författare)
-
Towards printable water-in-polymer salt electrolytes for high power organic batteries
- 2022
-
Ingår i: Journal of Power Sources. - : Elsevier. - 0378-7753 .- 1873-2755. ; 524
-
Tidskriftsartikel (refereegranskat)abstract
- Internet-of-things which requires electronics, energy convertor and storage must be low-cost, recyclable and environmentally friendly. In the development of printed batteries, ideally all the components (electrode and electrolyte) must be printable to ensure low-cost manufacturing via printing technologies. Most of the printed batteries suffer with low power. One of the reasons is the poor ionic conductivity of the electrolyte due to the high viscosity needed for printing relatively thick layers. In the present work we have demonstrated a new class of electrolyte promising for printed organic batteries following the concept of water-in-polymer salt electrolytes (WIPSEs). These highly concentrated electrolytes of potassium polyacrylate are non-flammable, low cost and environmentally friendly. They possess high ionic conductivities (45-87 mS/cm) independent on the macroscopic viscosities varying from 7 to 33000 cP. The decoupling between ionic transport and macroscopic viscosity enables us to demonstrate organic batteries based on WIPSEs that can deliver a high and constant power (similar to 4.5 kW/kg; 7.1-11 mW/cm(2)) independent on the viscosity of the electrolytes. The tunability of the viscosity presents a prerequisite for printed technology manufacturing and compatibility with printed batteries.
|
|
